View LM358DR_300365.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
D Wide Range of Supply Voltages:
- Single Supply . . . 3 V to 30 V (LM2904 and LM2904Q . . . 3 V to 26 V) or - Dual Supplies Low Supply-Current Drain Independent of Supply Voltage . . . 0.7 mA Typ Common-Mode Input Voltage Range Includes Ground, Allowing Direct Sensing Near Ground Low Input Bias and Offset Parameters: - Input Offset Voltage . . . 3 mV Typ A Versions . . . 2 mV Typ - Input Offset Current . . . 2 nA Typ - Input Bias Current . . . 20 nA Typ A Versions . . . 15 nA Typ Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage . . . 32 V (LM2904 and LM2904Q . . . 26 V) Open-Loop Differential Voltage Amplification . . . 100 V/mV Typ Internal Frequency Compensation
D D D
LM158, LM158A . . . JG PACKAGE LM258, LM258A . . . D OR P PACKAGE LM358 . . . D, DGK, P, PS, OR PW PACKAGE LM358A . . . D, DGK, OR P PACKAGE LM2904 . . . D, DGK, P, PS, OR PW PACKAGE LM2904Q . . . D PACKAGE (TOP VIEW)
1OUT 1IN- 1IN+ GND
1 2 3 4
8 7 6 5
VCC 2OUT 2IN- 2IN+
LM158, LM158A . . . FK PACKAGE (TOP VIEW)
D D D
NC 1OUT NC V CC+ NC NC 1IN- NC 1IN+ NC
4 5 6 7 8 3 2 1 20 19 18 17 16 15 14 9 10 11 12 13
NC 2OUT NC 2IN- NC
These devices consist of two independent, high-gain, frequency-compensated operational NC - No internal connection amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 30 V (3 V to 26 V for the LM2904 and LM2904Q), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be implemented more easily in single-supply-voltage systems. For example, these devices can be operated directly from the standard 5-V supply used in digital systems and easily can provide the required interface electronics without additional 5-V supplies. The LM2904Q is manufactured to demanding automotive requirements.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
On products compliant to MIL PRF 38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters.
Copyright 2003, Texas Instruments Incorporated
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
NC GND NC 2IN+ NC
description/ordering information
1
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
description/ordering information (continued)
ORDERING INFORMATION
TA VIOmax AT 25C PDIP (P) SOIC (D) 7 mV 0 C 70C 0C to 70 C SOP (PS) TSSOP (PW) VSSOP (DGK) PDIP (P) 3 mV SOIC (D) VSSOP (DGK) PDIP (P) 5 mV -25C to 85C 3 mV SOIC (D) PDIP (P) SOIC (D) PDIP (P) PACKAGE Tube of 50 Tube of 75 Reel of 2500 Reel of 2000 Tube of 150 Reel of 2000 Reel of 2500 Tube of 50 Tube of 75 Reel of 2500 Reel of 2500 Tube of 50 Tube of 75 Reel of 2500 Tube of 50 Tube of 75 Reel of 2500 Tube of 50 Tube of 75 Reel of 2500 SOIC (D) -40C to 125C -40 C 125 C 7 mV SOP (PS) TSSOP (PW) VSSOP (DGK) CDIP (JG) 5 mV -55C to 125C 2 mV LCCC (FK) CDIP (JG) Tube of 75 Reel of 2500 Reel of 2000 Tube of 150 Reel of 2000 Reel of 2500 Tube of 50 Tube of 55 Tube of 50 ORDERABLE PART NUMBER LM358P LM358D LM358DR LM358PSR LM358PW LM358PWR LM358DGKR LM358AP LM358AD LM358ADR LM358ADGKR LM258P LM258D LM258DR LM258AP LM258AD LM258ADR LM2904P LM2904D LM2904DR LM2904QD LM2904QDR LM2904PSR LM2904PW LM2904PWR LM2904DGKR LM158JG LM158FK LM158AJG L2904 MBS LM158JG LM158FK LM158AJG 2904Q L2904 LM2904 LM258A LM2904P LM258 LM258AP LM358A M6S LM258P L358 M5S LM358AP LM358 L358 TOP-SIDE MARKING LM358P
LCCC (FK) Tube of 55 LM158AFK LM158AFK Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package.
symbol (each amplifier)
IN+ IN- + - OUT
2
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
schematic (each amplifier)
VCC+ 6-A Current Regulator 6-A Current Regulator 100-A Current Regulator
IN-
OUT
IN+
50-A Current Regulator GND (or VCC-) To Other Amplifier COMPONENT COUNT Epi-FET Diodes Resistors Transistors Capacitors 1 2 7 51 2
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
3
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
LM158, LM158A LM258, LM258A LM358, LM358A Supply voltage, VCC (see Note 1) Differential input voltage, VID (see Note 2) Input voltage, VI (either input) Duration of output short circuit (one amplifier) to ground at (or below) 25C free-air temperature (VCC 15 V) (see Note 3) D package DGK package Package thermal impedance, JA (see Notes 4 and 5) P package PS package PW package Package thermal impedance, JC (see Notes 6 and 7) FK package JG package LM158, LM158A LM258, LM258A Operating free-air temperature range, TA LM358, LM358A LM2904, LM2904Q Operating virtual junction temperature, TJ Case temperature for 60 seconds Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds Storage temperature range, Tstg FK package JG package 150 260 300 -65 to 150 300 -65 to 150 16 or 32 32 -0.3 to 32 Unlimited 97 172 85 95 149 5.61 14.5 -55 to 125 -25 to 85 0 to 70 -40 to 125 150 C C C C LM2904 LM2904Q 13 or 26 26 -0.3 to 26 Unlimited 97 172 85 95 149 C/W C/W C/W UNIT V V V
C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages and VCC specified for measurement of IOS, are with respect to the network ground terminal. 2. Differential voltages are at IN+ with respect to IN-. 3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction. 4. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150C can affect reliability. 5. The package thermal impedance is calculated in accordance with JESD 51-7. 6. Maximum power dissipation is a function of TJ(max), JC, and TC. The maximum allowable power dissipation at any allowable case temperature is PD = (TJ(max) - TC)/JC. Operating at the absolute maximum TJ of 150C can affect reliability. 7. The package thermal impedance is calculated in accordance with MIL-STD-883.
4
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS VCC = 5 V to MAX, VIC = VICR(min), VO = 1.4 V TA MIN 25C Full range Full range 25C IIO aI Input offset current Average temperature coefficient of input offset current Input bias current VO = 1.4 V VO = 1.4 V Full range Full range 25C IIB Full range 25C VCC = 5 V to MAX Full range RL 2 k VOH High-level output voltage RL 10 k VCC = MAX VOL Low-level output voltage Large-signal differential voltage amplification Common-mode rejection ratio Supply-voltage rejection ratio (VDD/VIO) Crosstalk attenuation RL 10 k VCC = 15 V, VO = 1 V to 11 V, RL = 2 k VCC = 5 V to MAX, VIC = VICR(min) VCC = 5 V to MAX f = 1 kHz to 20 kHz VCC = 15 V, VID = 1 V, VO = 0 IO Output current VCC = 15 V, VID = -1 V, VO = 15 V VID = -1 V, VO = 200 mV VCC at 5 V, GND at -5 V, VO = 0 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V, No load RL = 2 k RL 10 k 25C 25C Full range Full range Full range 25C Full range 25C 50 25 70 80 26 27 28 5 100 20 25 15 65 80 dB 26 27 28 5 100 V/mV 20 mV V 0 to VCC-1.5 0 to VCC-2 VCC-1.5 10 -20 -150 -300 0 to VCC-1.5 0 to VCC-2 VCC-1.5 7 2 30 100 10 -20 -250 -500 nA VIO Input offset voltage Average temperature coefficient of input offset voltage LM158 LM258 TYP 3 MAX 5 7 7 2 50 150 nA MIN LM358 UNIT TYP 3 MAX 7 mV 9 V/C
aV
IO
IO
pA/C
VICR
Common-mode input voltage range
V
AVD CMRR
kSVR VO1/VO2
25C 25C 25C Full range 25C Full range 25C 25C Full range Full range
65
100 120
65
100 120
dB dB
-20 -10 10 5 12
-30 20 30 40 0.7 1 60 1.2 2
-20 -10 10 5 12
-30 20 30 40 0.7 1 60 1.2 2 mA mA
A mA
IOS
Short-circuit output current Supply current (two amplifiers)
ICC
All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for the LM2904 and 30 V for others. Full range is -55C to 125C for LM158, -25C to 85C for LM258, 0C to 70C for LM358, and -40C to 125C for LM2904 and LM2904Q. All typical values are at TA = 25C.
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
5
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS VCC = 5 V to MAX, VIC = VICR(min), VO = 1.4 V TA MIN 25C Full range Full range 25C IIO aI
IO
LM2904 LM2904Q TYP 3 MAX 7 10 7 2 50 300 10 -20 0 to VCC-1.5 0 to VCC-2 VCC-1.5 26 23 25 15 50 65 80 100 120 -20 -10 10 5 30 40 0.7 1 60 1.2 2 20 -30 24 5 100 20 -250 -500
UNIT
VIO aV
IO
Input offset voltage Average temperature coefficient of input offset voltage Input offset current Average temperature coefficient of input offset current Input bias current
mV V/C nA pA/C nA
VO = 1.4 V
Full range Full range 25C
IIB
VO = 1.4 V
Full range 25C
VICR
Common-mode input voltage range
VCC = 5 V to MAX Full range RL 2 k 25C 25C RL = 2 k RL 10 k Full range Full range Full range 25C Full range 25C 25C 25C 25C VCC = 15 V, VID = 1 V, VO = 0 Full range 25C VCC = 15 V, VID = -1 V, VO = 15 V VID = -1 V, VO = 200 mV VCC at 5 V, GND at -5 V, VO = 0 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V, No load Full range 25C 25C Full range Full range
V
VOH
High-level output voltage
RL 10 k VCC = MAX
V
VOL AVD CMRR kSVR VO1/VO2
Low-level output voltage Large-signal differential voltage amplification Common-mode rejection ratio Supply-voltage rejection ratio (VDD/VIO) Crosstalk attenuation
RL 10 k VCC = 15 V, VO = 1 V to 11 V, RL = 2 k VCC = 5 V to MAX, VIC = VICR(min) VCC = 5 V to MAX f = 1 kHz to 20 kHz
mV V/mV dB dB dB
IO
Output current
mA
A mA mA
IOS ICC
Short-circuit output current Supply current (two amplifiers)
All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for the LM2904 and 30 V for others. Full range is -55C to 125C for LM158, -25C to 85C for LM258, 0C to 70C for LM358, and -40C to 125C for LM2904 and LM2904Q. All typical values are at TA = 25C.
6
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS VCC = 5 V to 30 V, VIC = VICR(min), VO = 1.4 V TA 25C Full range Full range 25C IIO aI Input offset current Average temperature coefficient of input offset current Input bias current VO = 1.4 V VO = 1.4 V Full range Full range 25C IIB Full range 25C VCC = 30 V Full range RL 2 k VCC = 30 V RL 10 k VCC = 15 V, VO = 1 V to 11 V, RL = 2 k RL = 2 k RL 10 k 25C Full range Full range Full range 25C Full range 25C 50 25 70 80 0 to VCC-1.5 0 to VCC-2 VCC-1.5 26 27 28 5 100 20 50 25 70 80 dB 10 -15 7 2 MIN LM158A TYP MAX 2 4 15* 10 30 200 -50 -100 0 to VCC-1.5 0 to VCC-2 VCC-1.5 26 27 28 5 100 V/mV 20 mV 10 -15 7 2 MIN LM258A TYP 2 MAX 3 mV 4 15 15 30 200 -80 -100 nA nA V/C UNIT
VIO aV
Input offset voltage Average temperature coefficient of input offset voltage
IO
IO
pA/C
VICR
Common-mode input voltage range
V
VOH
High-level output voltage Low-level output voltage Large-signal differential voltage amplification Common-mode rejection ratio Supply-voltage rejection ratio (VDD/VIO) Crosstalk attenuation
V
VOL
AVD CMRR
kSVR VO1/VO2
25C f = 1 kHz to 20 kHz VCC = 15 V, VID = 1 V, VO = 0 25C 25C Full range 25C Full range 25C 25C Full range Full range
65
100 120
65
100 120
dB dB -60 mA
-20 -10 10 5 12
-30 20 30 40 0.7 1
-60
-20 -10 10 5 12
-30 20 30 40 0.7 1
IO
Output current
VCC = 15 V, VID = -1 V, VO = 15 VID = -1 V, VO = 200 mV VCC at 5 V, GND at -5 V, VO = 0 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V, No load
A 60 1.2 2 mA mA
IOS
Short-circuit output current Supply current (two amplifiers)
60 1.2 2
ICC
*On products compliant to MIL-PRF-38535, this parameter is not production tested. All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for LM2904 and 30 V for others. Full range is -55C to 125C for LM158A, -25C to 85C for LM258A, and 0C to 70C for LM358A. All typical values are at TA = 25C.
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
7
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS VCC = 5 V to 30 V, VIC = VICR(min), VO = 1.4 V TA 25C Full range Full range 25C IIO aI
IO
MIN
LM358A TYP 2
MAX 3 5
UNIT mV V/C nA pA/C nA
VIO aV
IO
Input offset voltage Average temperature coefficient of input offset voltage Input offset current Average temperature coefficient of input offset current Input bias current
7 2
20 30 75
VO = 1.4 V
Full range Full range 25C 10 -15 0 to VCC-1.5 0 to VCC-2 VCC-1.5 26 27 25 15 65 65 80 100 120 -20 -10 10 5 30 40 0.7 1 20 -30 28 5 100
300 -100 -200
IIB
VO = 1.4 V
Full range 25C
VICR
Common-mode input voltage range
VCC = 30 V Full range RL 2 k 25C RL = 2 k RL 10 k Full range Full range Full range 25C Full range 25C 25C f = 1 kHz to 20 kHz VCC = 15 V, VID = 1 V, VO = 0 25C 25C Full range 25C Full range 25C 25C Full range Full range
V
VOH VOL AVD CMRR kSVR VO1/VO2
High-level output voltage Low-level output voltage Large-signal differential voltage amplification Common-mode rejection ratio Supply-voltage rejection ratio (VDD/VIO) Crosstalk attenuation
VCC = 30 V RL 10 k
V 20 mV V/mV dB dB dB -60 mA
VCC = 15 V, VO = 1 V to 11 V, RL = 2 k
IO
Output current
VCC = 15 V, VID = -1 V, VO = 15 V VID = -1 V, VO = 200 mV VCC at 5 V, GND at -5 V, VO = 0 VO = 2.5 V, No load VCC = MAX, VO = 0.5 V No load
A 60 1.2 2 mA mA
IOS
Short-circuit output current
ICC
Supply current (two amplifiers)
All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for testing purposes is 26 V for LM2904 and 30 V for others. Full range is -55C to 125C for LM158A, -25C to 85C for LM258A, and 0C to 70C for LM358A. All typical values are at TA = 25C.
8
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
LM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
SLOS068H - JUNE 1976 - REVISED SPETEMBER 2003
operating conditions, VCC = 15 V, TA = 25C
PARAMETER SR B1 Vn Slew rate at unity gain Unity-gain bandwidth Equivalent input noise voltage TEST CONDITIONS RL = 1 M, CL = 30 pF, VI = 10 V (see Figure 1) RL = 1 M, CL = 20 pF (see Figure 1) RS = 100 , VI = 0 V, f = 1 kHz (see Figure 2) TYP 0.3 0.7 40 UNIT V/s MHz nV/Hz
VCC+ - VI + VCC- CL RL VO
Figure 1. Unity-Gain Amplifier
900 VCC+ - RS + VCC- VO
100 VI = 0 V
Figure 2. Noise-Test Circuit
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
9
MECHANICAL DATA
MCER001A - JANUARY 1995 - REVISED JANUARY 1997
JG (R-GDIP-T8)
0.400 (10,16) 0.355 (9,00) 8 5
CERAMIC DUAL-IN-LINE
0.280 (7,11) 0.245 (6,22)
1
4 0.065 (1,65) 0.045 (1,14)
0.063 (1,60) 0.015 (0,38)
0.020 (0,51) MIN
0.310 (7,87) 0.290 (7,37)
0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN
0.023 (0,58) 0.015 (0,38) 0.100 (2,54) 0.014 (0,36) 0.008 (0,20)
0-15
4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
1
MECHANICAL DATA
MLCC006B - OCTOBER 1996
FK (S-CQCC-N**)
28 TERMINAL SHOWN
LEADLESS CERAMIC CHIP CARRIER
18
17
16
15
14
13
12
NO. OF TERMINALS ** 11 10 28 9 8 7 6 68 5 84 44 52 20
A MIN 0.342 (8,69) 0.442 (11,23) 0.640 (16,26) 0.739 (18,78) 0.938 (23,83) 1.141 (28,99) MAX 0.358 (9,09) 0.458 (11,63) 0.660 (16,76) 0.761 (19,32) 0.962 (24,43) 1.165 (29,59) MIN 0.307 (7,80) 0.406 (10,31) 0.495 (12,58) 0.495 (12,58) 0.850 (21,6) 1.047 (26,6)
B MAX 0.358 (9,09) 0.458 (11,63) 0.560 (14,22) 0.560 (14,22) 0.858 (21,8) 1.063 (27,0)
19 20 21 B SQ 22 A SQ 23 24 25
26
27
28
1
2
3
4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25)
0.020 (0,51) 0.010 (0,25)
0.055 (1,40) 0.045 (1,14)
0.045 (1,14) 0.035 (0,89)
0.028 (0,71) 0.022 (0,54) 0.050 (1,27)
0.045 (1,14) 0.035 (0,89)
4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
1
MECHANICAL DATA
MPDI001A - JANUARY 1995 - REVISED JUNE 1999
P (R-PDIP-T8)
0.400 (10,60) 0.355 (9,02) 8 5
PLASTIC DUAL-IN-LINE
0.260 (6,60) 0.240 (6,10)
1
4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.015 (0,38) 0.200 (5,08) MAX Seating Plane 0.125 (3,18) MIN 0.010 (0,25) NOM Gage Plane
0.020 (0,51) MIN
0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) M
0.430 (10,92) MAX
4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
1
MECHANICAL DATA
MPDS028B - JUNE 1997 - REVISED SEPTEMBER 2001
DGK (R-PDSO-G8)
0,38 0,25 8 5
PLASTIC SMALL-OUTLINE PACKAGE
0,65
0,08 M
0,15 NOM 3,05 2,95 4,98 4,78
Gage Plane 0,25 1 3,05 2,95 4 0- 6 0,69 0,41
Seating Plane 1,07 MAX 0,15 0,05 0,10
4073329/C 08/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC MO-187
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
1
MECHANICAL DATA
MSOI002B - JANUARY 1995 - REVISED SEPTEMBER 2001
D (R-PDSO-G**)
8 PINS SHOWN 0.050 (1,27) 8 5 0.020 (0,51) 0.014 (0,35) 0.010 (0,25)
PLASTIC SMALL-OUTLINE PACKAGE
0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81)
0.008 (0,20) NOM
Gage Plane 1 A 4 0- 8 0.044 (1,12) 0.016 (0,40)
0.010 (0,25)
Seating Plane 0.069 (1,75) MAX 0.010 (0,25) 0.004 (0,10) 0.004 (0,10)
PINS ** DIM A MAX A MIN
8 0.197 (5,00) 0.189 (4,80)
14 0.344 (8,75) 0.337 (8,55)
16 0.394 (10,00) 0.386 (9,80)
4040047/E 09/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Falls within JEDEC MS-012
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
1
MECHANICAL DATA
MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999
PW (R-PDSO-G**)
14 PINS SHOWN
PLASTIC SMALL-OUTLINE PACKAGE
0,65 14 8
0,30 0,19
0,10 M
0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 A 7 0- 8 0,75 0,50
Seating Plane 1,20 MAX 0,15 0,05 0,10
PINS ** DIM A MAX
8
14
16
20
24
28
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
1
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless

▲Up To Search▲

Price & Availability of LM358DR

	To Download LM358DR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .